Most electrical problems get poked at before anyone calls. A breaker gets reset. An outlet gets tested with a different plug. A light switch gets flipped a few times hoping something changes. That is a reasonable first step, and sometimes it is enough. The point at which it stops being enough is when the symptom comes back, when you cannot find a clear reason for it, or when what you are looking at involves the panel, the wiring inside the wall, or anything that has already gotten warm or started to smell. That is where we come in.
We handle electrical repairs, panel upgrades, new circuits, lighting, and a full range of residential and commercial electrical work for homes and properties in Summit.
Whether it is a single outlet that stopped working or a panel that cannot carry the load the property now puts through it, call (262) 955-2829 for a quote. We are available every day from 6:00 AM to 9:30 PM.
Every job ends the same way. We test the work before we leave. Outlets are checked under load, not just with a meter. Breakers are cycled. GFCI and AFCI protection is confirmed where it is required. If a circuit was added or modified, the panel directory gets updated to reflect what is actually on it.
That documentation matters more than it might seem at first. When a property sells, or when a tenant moves out and a landlord needs to account for what was done, a clear and accurate panel directory is the difference between a clean inspection and a set of questions nobody can answer. We take pride in the electrical work we leave behind, and that starts with leaving the property in a state that holds up to scrutiny later.
Older homes in this part of Wisconsin frequently turn up grounding and bonding gaps that were never addressed when the house was built or when circuits were added over the years. A ground that is missing or improperly run is not always obvious from the outside. Neither is a neutral-to-ground connection that is in the wrong place. We check both as part of any panel or wiring work, not as an add-on.
Arc-fault and ground-fault breakers are now required in most living areas and in all wet locations. Homes that predate those requirements often have neither, which is a gap worth closing. When we are already in the panel, we note what is missing and explain what adding it involves.
Summit has homes that carry wiring from a different era. Knob-and-tube runs without a ground and uses insulation that degrades over time. It cannot support three-prong outlets without additional work, and it is not compatible with the insulation that gets blown into walls during energy upgrades. Aluminum branch-circuit wiring from a later period carries its own risks at connections and devices, where the metal's expansion and contraction over years of use can loosen terminations.
Neither situation is an automatic emergency, but both warrant an honest assessment. We explain what we find, what it means for the property, and what the remediation options are. The fault traced before anything is replaced.
Scheduling a service call is simple.
Call (262) 955-2829, describe what you are seeing, and we scope the job on the call.
You get a price and a plain explanation of what the work involves before anything is put on the calendar. We are available every day from 6:00 AM to 9:30 PM, including weekends, which means a repair that comes up on a Saturday does not have to wait until Monday.
For properties with tenants or for a small business that cannot shut down a space, we talk through the timing before the visit. A circuit that feeds a refrigerator or a point-of-sale system needs to be handled differently from one that feeds a spare bedroom. That conversation happens on the call, not at the door. We treat your home the way we would want ours treated, and that same approach carries over to every rental unit and commercial space we work in.
When a problem will not keep, call and describe what you are seeing. Sparks, a burning smell, an outlet that is warm to the touch, or a breaker that will not reset after tripping are all situations we want to hear about promptly. We take short-notice work, and the call is where we assess what the situation requires.
Homes in a town this size tend to carry history. Original wiring from decades past, circuits added by previous owners without documentation, panels that were sized for a fraction of what the property now draws. The jobs below come up regularly here, and each one starts with a situation rather than a catalog entry.
A generator that is not properly wired to the panel is not a backup. It is a cord running through a window. A correct hookup involves a transfer switch that isolates the generator from the utility line, wiring from the panel to the connection point, and a load calculation to confirm the generator is matched to what the panel can carry. Without the transfer switch, power fed back onto the utility line is a hazard to anyone working on it. We handle the full electrical side of the hookup.
A large appliance, a chest freezer in the garage, or a new dishwasher all run better on a circuit they do not share. A dedicated circuit is sized to the appliance, run from the panel, and protected by a breaker matched to the load. Before any dedicated circuit is added, we check whether the panel has the capacity to carry it. If it does not, that conversation happens before the work starts, not after.
A Level 2 EV charger runs on a 240-volt dedicated circuit. The panel assessment comes first, because adding that circuit to a panel that is already near capacity is a different project from adding it to one with room to spare. Welders, air compressors, and workshop equipment follow the same logic. High-draw tools need circuits sized to their starting and running loads, not just their nameplate wattage. Getting that sizing right on the front end prevents nuisance tripping and protects the equipment.
Aluminum branch-circuit wiring does not need to be replaced wholesale in most cases. The risk concentrates at the terminations, where aluminum meets the screws and lugs of outlets, switches, and fixtures. Remediation typically involves pigtailing with approved connectors at every device, using CO/ALR-rated outlets and switches where required, and inspecting the panel connections. We document what was done so the work is traceable when the property changes hands.
A smart switch or dimmer is a straightforward swap in a box that already has the right wiring. In an older home, it often is not that simple. Many smart switches require a neutral wire at the box, which older wiring configurations do not always provide. Dimmers need to be matched to the fixture type, because a dimmer rated for incandescent bulbs will not work correctly with LED loads. We check the box and the circuit before recommending a device, not after.
A quote is built from what the job actually involves. The things that move a price are the fault itself once it is traced, what has to be opened up to reach it, and whether the existing circuit or panel can carry what is being added. A straightforward outlet replacement and a wiring fault buried inside a finished wall are different jobs, and the price reflects that difference.
You get the rate on the phone, based on what you describe and what the job typically involves at that scope. If the work turns out to be different from what the call suggested, we explain that before proceeding. The price is confirmed before anything is scheduled. Call us and we'll walk you through the fix. For a job in Summit, our services page is a good starting point.
Most electrical work that goes beyond a straight device swap requires a permit and inspection. New circuits, panel upgrades, service entrance work, and rewiring projects are the common ones. The permit is filed before the work starts, and the inspection happens after it is complete. We handle the filing as part of the job.
The specific requirements vary depending on whether the property is within municipal limits or in an unincorporated part of the county, and they can differ between a residential and a commercial project. We confirm what applies at your address before anything is scheduled.
Call (262) 955-2829 and ask if you are not sure what a particular job requires.
Summit sits within Waukesha County, and we cover the surrounding communities as well. Dousman, Oconomowoc, Oconomowoc Lake, Nashotah, and Delafield are all within our service area. If you are managing a property or scheduling work anywhere in this part of the county, the call is the same and the process is the same.
We work on homes, rental units, small commercial spaces, and outbuildings across the area.
Call (262) 955-2829 and we will confirm coverage for your address.
Yes. We assess the existing work as part of taking it on, so we know what was done correctly and what may need to be revisited. We do not assume previous work is up to standard without checking it. Call and describe the situation and we will tell you what the assessment involves.
An inspection covers the panel, the branch circuits, the outlets, the grounding, and the visible wiring throughout the home. We look at whether GFCI and AFCI protection is in place where it is now required, check for signs of deteriorating insulation or improper connections, and assess whether the panel is appropriately sized for the load the home actually carries. Older homes in this area often turn up knob-and-tube wiring, aluminum branch circuits, or panels that were never upgraded to match the load. The inspection gives you a clear picture of what is there and what, if anything, warrants attention.
Call and describe what the inspection report noted. We scope the work on the call, explain what each item involves, and confirm the price before anything is scheduled. If the items require a permit and re-inspection, we handle the filing and coordinate the timing so the work is documented and traceable when the transaction closes. Buyers and their agents want to see that flagged items were addressed by someone who can account for the work, and we provide that documentation as part of the job.
Yes.
Call (262) 955-2829 and walk us through what the other quote covers.
We can tell you what the work involves, what drives the cost, and whether the scope sounds right for the problem described. You are not committed to anything by asking.
We ask about the schedule when the job is booked and plan the work around the times that work best for the operation. Some jobs can be staged or sequenced so disruption is limited to the quieter parts of the week. Call and describe the schedule and we will work through the options.
Stop using the circuit and leave the breaker in the off position. Forcing a breaker that will not reset can damage the panel or mask a fault that needs to be found.
Call (262) 955-2829 and describe what happened so we can help you assess how urgently the situation needs to be addressed.
Landscape and driveway lighting runs on a dedicated circuit from the panel, with wiring run underground in conduit or direct-burial cable to the fixture locations. Low-voltage landscape systems use a transformer fed from a standard circuit. We handle both the circuit work and the wiring to the fixtures.
Describing what you are seeing is enough. A sound, a smell, a symptom that keeps coming back, a circuit that stopped behaving the way it should.
Call (262) 955-2829 and someone who knows the trade will ask the right questions and scope the job from there. Plain answers. Clear options. Safe wiring.
We are available every day from 6:00 AM to 9:30 PM.
Call (262) 955-2829 and let Waukesha Electrical Company handle the rest.
We take electrical work in these nearby communities as well: Oconomowoc, Delafield, Okauchee Lake, Wales, Hartland. Everywhere else we go is in our full list of communities.
Electrical problems show up in all shapes and sizes, from a single dead outlet to a panel that can no longer carry the load a modern home puts through it. We handle the full range of residential and commercial electrical work across Summit and the surrounding county, every day from 6:00 AM to 9:30 PM. The table below covers what each service involves, who it fits best, and what is worth knowing before you call. Call for a quote and we will scope the job on the phone before anything is scheduled.
| Service Type | What It Covers | Ideal For | Worth Knowing |
|---|---|---|---|
| Whole-Home Surge Protection | Panel-mounted surge device installation, Protection for all circuits in the home, Pairing with panel upgrades | Homes with sensitive electronics or appliances vulnerable to voltage spikes | Surge damage from utility switching events or lightning is not always immediately visible. Panel-mounted protection is the most effective option and installs in a single visit. |
| Ceiling Fan Installation | Fan and wiring installation, Ceiling box upgrade where needed, Switch and control wiring | Rooms without an existing ceiling box or with an undersized junction box | Fans require a rated ceiling box to handle the weight and movement. If one is not in place, we install it as part of the same visit. |
| Electrical Panel and Service Upgrades | 200-amp service upgrade, Load calculation and panel sizing, Subpanel additions for garages or additions | Homes adding EV chargers, electric heating circuits, or significant new load | A 100-amp panel that was adequate years ago often falls short once modern appliances and charging equipment are in the picture. We confirm capacity before the work starts. |
Call (262) 955-2829 and we will walk through what the work involves, confirm the price, and get you on the schedule.
(262) 955-2829